
A 2 way only is powered up
and down and a assistant
would
be required to push
the patient along the rail
where as a 4
way is powered both up & down and side to side. |
|
 |
| |
|
|

A 2 way only is powered up
and down and a assistant
would
be required to push the patient along the rail where as
a 4
way is powered both up
& down and side to side. |
|
 |
| |
|
|

The Voyager 800 is only offered as a 4
way lift. |
|
 |
| |
|
|

This is a track changer allowing you to
switch track from one direction to the other. A 45 Degree
Changer will turn 45 degree and stop. A 90 Degree
Changer will turn 90 degrees
and stop. |
|
 |
| |
|
|
| 76 Meter Tracks
The 76 meter tracks must be supported
by a bracket every 36 inches and has should only be used with the
Voyager 420
All track sections include all required
bracket's, End Stop's, Trolley's and hardware
required to install
them. |
|
 |
| |
|
|
| 144
Meter Tracks
The 144 meter tracks can span a 19.6
Ft distance with only support on each end. Use with the
Voyager 420, 550, 800, V-3, V-4, The Portable and the Griffin.
All track sections include all required
bracket's, End Stop's, Trolley's and hardware
required to install
them. |
|
 |
| |
|
|
| 30 Degree Curve All track sections include all required
bracket's, spacers, washers and hardware
required to install
them. |
|
 |
| |
|
|
| 45 Degree Curve All track sections include all required
bracket's, spacers, washers and hardware
required to install
them. |
|
 |
| |
|
|
| 70 Degree Curve All track sections include all required
bracket's, spacers, washers and hardware
required to install
them. |
|
 |
| |
|
|
| 90
Degree Curve All track sections include all required
bracket's, spacers, washers and hardware
required to install
them. |
|
 |
| |
|
|
| Pivoting Wall Bracket
The Pivoting Wall Bracket allows you to support the
rail from a wall instead of the ceiling. This Bracket requires
wall modifications as it is
meant to be bolted to two
2 X 4 studs. |
|
 |
| |
|
|
| Wall Post & Bracket
The Wall Post Bracket allows you to support the rail from a wall
instead of the ceiling. This
post extends to the floor
providing little strain on the
wall and bearing most of the weight or support from the floor. |
|
 |
| |
|
|
| End Stop
The End Stop is used at the
end of a rail run to cap off
and secure the end to stop
the lift when it reaches the
end. |
|
 |
| |
|
|
| End Rail Charger
The End Rail Charger serves
to uses. 1st it serves as a
End Stop 2nd it serves as
a automatic charger for the
lift. ( Please Note ) that you
automatically receive one of
these with the purchase of
your lift. |
|
 |
| |
|
|
| Standard Track Bracket
The Standard
Track Bracket
is used to support rail to the ceiling. They are secured to the
ceiling using a 3" Inch lag
bolt. ( Please Note ) that you
automatically receive all the
brackets you will require with each section of rail ordered
above. |
|
 |
| |
|
|
| Long Track Bracket
The Long
Track Bracket
is used to connect two rails together. This bracket is not
an absolute requirement. Many installations are done using only
stand brackets. |
|
 |
| |
|
|
| Cathedral Bracket
The Cathedral Bracket
is used for slanted ceilings. Additional brackets or support may
be needed with this type
of application. |
|
 |
| |
|
|
| Visible Lateral Brace
The Visible Lateral Brace is used to support the rail by picking
up support from 0
to 90 degree angle off a wall
or the ceiling. |
|
 |
| |
|
|
Adjustable Lateral Brace
The Adjustable Lateral Brace is used to support the rail by picking
up support from a 0
to 90 degree angle off a wall
or the ceiling. |
|
 |
| |
|
|
Track Junction
The Track Junction is used to
connect support (3) track's at (1) point this is used with the
Portable Voyager or (2) Standard Voyager Lifts. The
only other time this bracket is used is when you simply want to use a section of
rail to pick up support 90 degrees to the side. |
|
 |
| |
|
|
Joint Kit
The Joint Kit is used to add support to the joining of two
rails however is not required and offers more of a cosmetic service. |
|
 |
| |
|
|
Long Joint Kit
The Long Joint Kit is used to add support to the joining of two
rails as is the standard joint kit however the long kit gives added support to
the joining of the two rails. Again is not required. |
|
 |
| |
|
|
Reverse Bracket
The Reverse Bracket with Joint Kit Is used when you are using a
turn. The turning rail can be used to go in ether direction yet
the teeth change direction depending on the end that is used to attach to. This
bracket can be replaced by simply using two standard brackets at the union. |
|
 |
| |
|
|
X-Y Gate System
The X-Y Gate System is used to join one track to ride on two other
tracks, giving a lift the full virtual range of the square the
tracks cover. This application is mostly found in hospitals or medical facility
as they service many different size patients. |
|
 |
1/4 Shim
The 1/4 Shim is used to space brackets as nearly all ceilings are
not perfectly flat or flush. |
|
 |
| |
|
|
1/4 Shim
The 1/4 Shim is used to space brackets as nearly all ceilings are
not perfectly flat or flush. |
|
 |
| |

The New Polaris |
|