Straight or Adjacent Access Unit

• Carefully unpackage the Commercial Trust-T-Lift components, confirm the following parts as shown in Fig. 1 are included:

• Remove the front panel from the Trust-T-Lift Unit as shown in Fig. 3.

• Insert the (2X) 5/8"X3" Carriage Bolts and 5/8" Jam Nuts into the Lower Mechanical Stop brackets on the underside of the guide frame as shown in Fig. 4. Thread the bolts into the Mechanical stops about ½", they will be adjusted and jammed into place towards the end on the installation.

• Mount the Control Wall Extension to the Guide Frame as shown in Fig. 5A/5B.
• Fasteners- (6X) 10/32 X ½" Flathead screws with (6X) Chrome Finishing Washers

FIG. 5B- FASTENING CONTROL WALL EXTENSION TO GUIDE FRAME

• Mount the Carriage Gate Interlock to the Solid Hand Rail for a Straight Unit and to the Corner Post for an Adjacent Unit as shown in Fig. 11
• Fasteners- (2X) 10/32 X 1½" Screws

• Adjustment of the Interlock Key Tab may be necessary to allow proper alignment, loosen the (2X) 10/32 X ½" screws mounting it to the Aluminum Gate Tab and adjust as necessary as shown in Fig. 12

• Adjust the Spring Loaded Hinge on the Carriage Gate as shown in Fig. 13, this allows the gate to self-close against the Interlock.
• Use a 5/32" Allen Key to release the tension on the loaded spring (turn clock wise)
• Remove the set pin from the hinge
• Increase tension (clock wise) or decrease tension (counter clock wise) and reinsert the set pin

• Fasten the Carriage Gate Interlock Cable to the Safety Plate under the Toe Plate using the plastic Nylon Tie Straps provided as shown in Fig. 14

• Mount the Upper Gate to the threshold at the upper landing as in Fig.15
• Drill through the 5" X 5" Angle on the Upper Gate frame at suitable locations to provide adequate mounting holes for the angle, lag bolt or screw into place. OR Use a Polyurethane Adhesive to mount the threshold to the upper landing

• Use a Polyurethane Adhesive to mount the Upper Gate Post uprights to the existing structure as in Fig. 16
• When using the Polyurethane Adhesive adequate clamping and support must be in place until the adhesive sets properly (NOTE CLAMP IN FIG. 16)

• Mount the Lower Remote Call Station in a suitable location as in Fig. 17
• Run electrical conduit from the call station to the Outside Junction Box as well as from the Upper Gate to the Outside Junction Box located on the bottom left side of the Trust-T-Lift tower
• Run the cables from the Call Station and Upper Gate through the conduit to the Outside Junction Box

• The wires from the call station and Upper Gate and/or Interlocks are labeled with numbers that match the labels on the wires in the Outside Junction Box. The Outside Junction box is located at the bottom left side of the tower. Use the wire marrets provided to make the connections as in Fig. 18. (Unplug unit from power source before wiring)
• Plug the unit in or hard wire it to an outlet providing 120 V.A.C. and 15 AMP protection

• The Interlocks (both on the carriage and the upper gate) should be in the "Locked" Position as in Fig. 19 for the Trust-T-Lift unit to run.

• Run the lift up and adjust the Lower Mechanical Stops so the lift stops at the bottom by breaking the Lower Limit circuit as apposed to activating the Safety Plate circuit, once adjusted use the jam nuts to lock them into place as in Fig. 20.
  
  
• The electrical limit switch stop for the upper landing is controlled by adjusting the Upper Limit Adjusting Bracket as described in the Trust-T-Lift Installation Manual on page 2-7 Fig.17

• Mount the tower to the existing structure as in Fig. 21. Instructions are included with the tower-mounting angle

• Reinstall the Front panel into the Trust-T-Lift Unit as in Fig. 22